It does the job just fine for me. I am missing the shutoff valve right below it. The big fail is the angle of that top line pressure valve. It gets in the way of a wrench. It makes it more difficult to turn on and off gas. The plus side is the line attached to the bottom is positioned away from the 50 gal C02 tank we use. We've gone through 30+ taprites 10+ micromatics at this facility and this is my least favorite even though it performs flawlessly. The design is bad. We use it for pouring kegs exclusively. For a homebrewer its manageable and designed with homebrewing in mind. The ability to switch parts out easily seems great. The knob for adjusting c02 is my favorite. (We typically use higher pressures for water at his facility)

My old regulator failed research led me to 2 and I bought this KOMOS regulator have been extremely pleased. My ONLY complaint is that the connection to the tank is a tiny bit too short...an extra 1" would be perfect though it's still fine as-is. It connected easily leak-tested just fine and when I hooked everything back up I was pleased to regulate pressure down to just 2 PSI wow. The pressure knob has a good feel and is non-slippery is very responsive and it's quick 'n easy to dial-in precise pressures. I also like the gauges having knurly rubber bumpers built-in to provide basic protection though I'd recommend a protection basket if your environment warrants it. If you use 8mm OD DuoTight fittings and hoses like I do you'll love this regulator...it's already included!

I bought a special machine that needed a regulator that had a working pressure of at least 75 psi. Most regulators have a release valve that gives up at 62 psi. but by purchasing the 100 psi accessory I was able to simply change out the valve in a matter of a few seconds and it has been working great so far. Thanks for having great products and for being helpful when I emailed.

Decided to upgrade my regulator that came with my kegerator with this one. Everything is great but as others have pointed out the output gauge is way overrated. It should be in the 0 to 60 psi range. Makes setting a typical serving pressure almost impossible. I might switch the gauge with the other regulator’s output gauge.

Love it work great. I would recommend it good quality

Works like a champ. Even comes with extra washer

Needs gas line output shutoff valve with check valve. Output gauge range is too high for typical 8-12 psi serving pressure accuracy. Adjustment valve is designed for fine tuning of higher pressures than 8-12 psi serving pressure. Bottom line: can’t trust output pressure setting. Otherwise generally good.

Bought for its compatibility with Evabarrier/Duotight lines. So far so good. Wish it had a ball valve or shutoff ahead of the outlet though.

Easy to adjust and holds settings with no issue. One word of caution for those using the duotight fitting it comes with I had to tighten it more than the 1/4 turn past finger tight that I was able to use on the gas/liquid disconnects. Just go slow and be careful not to crack the threads.

Works great. No real issues with the regulator. I would recommend.

Installed the regulator with the Duotights and it was solid leak free. Though as some others have stated the pressure dial is just too damn small. A serving pressure of 12psi can barely be seen with the large scale.

So far I have only used the Komos regulator for my first ever kegged batch of homebrew in a 5 gallon ball lock keg and it's performing very well. The only thing I might change is on the gauge for keg pressure rather than 2 point increments it would be nice to have a more precise 1 point increments. Other than that I am happy with my purchase and looking forward to many years or use from it.

I had to get used to the flip-flopped location of the tank vs. output gauges compared to my other regulator but works very well. Solid. Also bought the gauge protector which I'm returning because it is insanely heavy.

Finally no more leaks!! The duotight fitting on this thing are a game changer.

I bought this because frankly I'm sick of tearing my hands apart with the dial valve knob on my other regulator. However where I feel this product misses the mark for me is that I am unable to take the current MFL nipple off in order to add a on/off valve before the nipple. I'll have to install a short connectors of EVABarrier and a Duotight ball valve to make up for that.

I like this regulator but I just wish it had a valve included. Otherwise no problems and easy to adjust with the large knob

Works just as it should

My old regulator was from the 80's; it gave up the ghost and I could not find a rebuild kit for it. I took the plunge and bought the Komos. I had it attached and working in 5 mins flat. I have a larger 20 lb CO2 tank and there were no problems at all. Near silent operation is a plus. Bottom line for me :: it works and I don't have to think about it.

I bought this for easy compatibility with Duotight fittings and couldn't be happier! Ive used numerous regulators over the years thinking each was a good upgrade. NONE compare to the quality and design of this!

Very impressed with the quality of this regulator. Defiantly an upgrade from my old now broken regulator.

I purchased this regulator for my son to use on a Cornelius keg filled with beer from a local brewery. With the purchase of this regulator his birthday gift was complete. He has been very happy with it.

Nice gas regulator. Holds steady pressure seems sturdy. Has built in PRV.

bought a 2nd reg for my fermentation chamber to do pressure ferments and closed transfers etc. Solidly built and guarded gauges are great. the regulator valve for adjustment is tricky touchy but just takes some getting used to

As advertised solid system for the price. Bought as a backup mainly.

Solid. Ready to use out of the box.